欧美亚洲国产精品久久久久_四虎国产精品永免费_亚洲AV成人无码久久WWW_国产麻豆媒一区一区二区三区,成人影视在线播放,都市激情校园春色亚洲,一二三四社区在线中文视频

  • 【產品導航】 Product navigation
  • 熱門產品:LX(XL)星形彈性聯軸器 | UL輪胎式聯軸器 | 帶制動輪鼓形齒式聯軸器 | 凸緣聯軸器 | 萬向聯軸器 | 彈性柱銷聯軸器
  • 【點擊排行】
    咨詢電話:086-0317-8309802
    E-mail:btlzqc@163.com

  • 【公司動態】
  • ■ 您當前所在位置: 聯軸器 > 行業動態 > 公司動態 >
  • 聯軸器偏差說明
    時間:2018-12-17 10:32 作者:聯軸器 點擊:
    聯軸器偏差說明

            聯軸器的偏差說明

       1、彈性聯軸器可傳遞扭矩和回轉角度,同時吸收軸的   偏差,當安裝偏差超過容許值時,可能會產生振動或導致聯軸器的壽命縮短,因此要偏差的調整適當。

      2、軸的偏差有三種,分別是徑向偏差、角向偏差和軸向偏差。請調整偏差,使其低于各產品規格表中列出的容許值。

      3、各產品所列之   大偏差容許值是指只有一種偏差存在的情況下,當兩種或   多種偏差同時存在時,容許值應低于各規格表中   大偏差的1/2。

      4、偏差并不只有發生在設備裝配,工作過程中的振動、熱膨脹、軸承磨損等都會引起偏差。因此,建議將軸向偏差調整至低于   大值1/3。

    Allgnment Adjustment

     1,Flexible couplings transmit torque and rotational angle while absorbing misalignment.When the misalignment exceeds allowable values,vibration may result or the life of the coupling may become shortened.Make sure to adjust the alignment accordingly.

     2,There are three types of shaft misalignment,namely in terms of parallel misalignment,angular misalignment and shaft end-play.Adjust the alignment to be below allowable values listed in the specification table of each product provided in this catalog.

     3,The maximum misalignment listed in this catalog is the allowable value when only one of the misalignments exists.In case two or more misalignments exist at the same time,the allowable values will be less than 1/2 of the maximum misalignment listed in the specification tables.

     4,Misalignments are sometimes caused not only by equipment assembly,but also by vibration,heat expansion,wear of bearings,ect.during operation.Therefore,it is recommended to adjust the shaft misalignment to be below 1/3 of maximum values.

    軸與軸聯接過程出現的偏差說明

    1 徑向偏差 parallel offset Misallgnment

      安裝時,兩軸平行但中心不在同一直線上,這時產生的偏差稱為徑向偏差。

     

    2 角向偏差 Symmetrical Angular Misalignment

      安裝時,兩軸中心線互成一個角度,這時產生的偏差稱為角向偏差。

     

    3 軸向偏差 End-play

      由于機械原因產生的軸間往復微動的偏差稱為軸向偏差。

     

    4 復合偏差 Combined Misalignment

      由1、2、3產生的偏差組合稱為復合偏差。 

    泊頭市利永聯軸器有限公司 生產各種聯軸器 聯軸器配件 聯軸器膜片等 打造客戶所需要的聯軸器 支持拿圖拿樣定制聯軸器 利永聯軸器專注于每一件產品 傳動聯軸專家 聯系電話:15128789423 

     

     相關動態
     相關產品
    主站蜘蛛池模板: 淳安县| 大荔县| 和静县| 佳木斯市| 和田市| 嘉定区| 车险| 屯门区| 宁津县| 土默特左旗| 保康县| 历史| 桓台县| 巫山县| 临猗县| 建始县| 昌宁县| 建昌县| 邵阳县| 麻栗坡县| 建德市| 讷河市| 嘉祥县| 施甸县| 甘德县| 鄂温| 齐齐哈尔市| 无棣县| 开封市| 龙泉市| 舞阳县| 射阳县| 辽源市| 六安市| 龙海市| 莲花县| 绥中县| 延安市| 诸城市| 济宁市| 安达市|